Tap Extractors
Remove broken taps – and save the threads
Walton Tap Extractors let you remove broken machine screw and hand taps, pipe taps and STI taps without drilling, lasers, damaged threads, scrapped parts or repair inserts.
The hardened steel fingers of these extraction tools fit in the flutes of a broken tap to back it out simply and safely. This effective method has been used since 1908. Tap Extractors are available in every tap size – both inch and metric – as handy sets or individual pieces. They will fit both NC and NF taps.
Walton Tap Extractors are designed specifically for:
- #4 to 1-1/2” machine screw and hand taps
- 3mm to 38mm taps, in all standard flute sizes
- 1/8” to 1” pipe taps
- #4 to 5/8” helical coil “STI” taps
Remove broken taps in 3 easy steps!
Find a local distributor
Specifications & Ordering Information
- Do not use the abbreviation “EXT.” on your orders. This could refer to either “Extensions” or “Extractors.”
- All orders for complete Tap Extractors and all replacement parts must clearly specify the flute style required. Each table shows, by size, the flute style
for which that size is standard. Parts are not interchangeable between the different flute styles. - When ordering replacement parts, refer to the parts illustration below for correct part name.
- Standard Sets contain sizes and flute styles as shown in our ordering information. Order by Set Number. Sets containing the same sizes but in non-standard flute styles will be made up on request at no extra charge.
- Orders for Pipe Tap Extractors and replacement parts must clearly specify “Pipe Tap” and indicate required flute style.
- Orders for STI Tap Extractors and replacement parts must clearly specify “STI” (Screw Thread Insert) and indicate flute style required.
- Threads per inch need not be specified, as Tap Extractors will fit both NC and NF taps.
Standard Extractors for Machine Screw & Hand Taps
UPC No. 054808
Single Tap Extractors & Replacement Parts
6-Flute
4-Flute
3-Flute
2-Flute
6-Flute
4-Flute
3-Flute
2-Flute
EDP Part No. shown indicates available flute style for each size. 4-Flute style supplied, where available, unless otherwise specified. Parts are not interchangeable between flute styles. Also available in Complete Production Range Sets, as shown on the following tab.
* For replacement fingers, minimum package quantity is 12.
Tap Extractor Sets
Each set is packed in sturdy plastic compartmented case. Sets 1, 2 and 3 are packed in a 6-compartment case (left). Sets 11, 13 and 15 are packed in a 15-compartment case (right).
UPC No. 054808
18001
18002
18003
18011
18013
18015
* 3-Flute style supplied for sizes shown. All others in 4-Flute style.
PLASTIC SET CASES (empty):
For Set Nos. 1, 2, 3 – 18501
For Set Nos. 11, 13, 15 – 18511
Tap Extractors for Pipe Taps
WALTON Tap Extractors, designed to fit Pipe Taps, are stocked in the following standard sizes and flute styles:
UPC No. 054808
Single Pipe Tap Extractors & Replacement Parts
5-Flute
4-Flute
5-Flute
4-Flute
EDP Part No. shown indicates available flute style for each size.
Tap Extractors for STI Taps
Helical Coil Wire Screw Thread Insert Taps
WALTON Tap Extractors, designed to fit all wire screw thread insert STI taps, are stocked in the following standard sizes and flute styles:
UPC No. 054808
Single STI Tap Extractors & Replacement Parts
4-Flute
3-Flute
2-Flute
4-Flute
3-Flute
2-Flute
EDP Part No. shown indicates available flute style for each size.
WARNING: This product contains lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm.
For more information: www.P65Warnings.ca.gov.